TEKTON 5547 4-Ton Dual Gear Power Puller

TEKTON 5755 46-pc. Harmonic Balance Puller
1-pc. Yoke
   1-pc. Center Screw
   3-pc. Center Screw Tip Adapters
   3-pc. 3/8" (24 TPI) x 1-1/2" Puller Bolts
   3-pc. 3/8" (16 TPI) x 2" Puller Bolts
   3-pc. 3/8" (16 TPI) x 3" Puller Bolts
   2-pc. 3/8" (16 TPI) x 4-1/2" Puller Bolts
   2-pc. 5/16" (18 TPI) x 6" Puller Bolts  
   3-pc. 5/16" (18 TPI) x 3-1/2" Puller Bolts
   2-pc. 5/16" (24 TPI) x 3" Puller Bolts
   3-pc. 5/16" Washers  
   2-pc. 1/4" (28 TPI) x 2-1/2" Puller Bolts
   2-pc. 1/4" Washers  
   3-pc. M10 (1.5mm) x 35mm Puller Bolts
   3-pc. 10mm Washers  
   3-pc. M8 (1.25mm) x 45mm Puller Bolts
   2-pc. M8 (1.25mm) x 65mm Puller Bolts
   2-pc. M8 (1.25mm) x 90mm Puller Bolts
   3-pc. 8mm Washers

1/4" Sq/Hex Quick-Change Adapter for your power drill.
   See 31 piece Mega Magnetic Driver Set 60085

1/4" Sq/Sq Adapters for ratchet handle drivers.
   See 31 piece Mega Magnetic Driver Set 60085

1/4" Sq/Hex Adapters for ratchet handle drivers.
   See 31 piece Mega Magnetic Driver Set 60085

TEKTON 5650 5-1/4" Suction Cup Dent Puller

TEKTON 5741 Seal Puller

Chrome vanadium steel nutdriver with lobular design and 1" hollow shafts.
   See 31 piece Mega Magnetic Driver Set 60085

Chrome vanadium steel nutdriver with lobular design and 1" hollow shafts.
   See 31 piece Mega Magnetic Driver Set 60085

Chrome vanadium steel nutdriver with lobular design and 1" hollow shafts.
   See 31 piece Mega Magnetic Driver Set 60085

Chrome vanadium steel nutdriver with lobular design and 1" hollow shafts.
   See 31 piece Mega Magnetic Driver Set 60085

Chrome vanadium steel nutdriver with lobular design and 1" hollow shafts.
   See 31 piece Mega Magnetic Driver Set 60085

TEKTON 5652 4" Suction Cup Dent Puller

TEKTON 5732 12" Ball Joint Separator

TEKTON 5681 3" 2-Jaw Gear Puller

TEKTON 5733 16" Tie Rod Separator

Mega-Magnetic Bit Holder - 2 powerful magnets create 40x the pulling power of an ordinary magnetic bit holder. Patented in USA.
   Magnet #1 holds and magnetizes the bit while magnet #2 powerfull

TEKTON 5680 3" 3-Jaw Gear Puller

Use With 3/8" drive for hard-to-reach Oil and Grease Seals, Simply insert hook behind seal and pull, Two hook sizes to fit most oil and grease seals, Can also be used with a breaker bar for extra reach or leverage, If the puller tips wear, resharpen on a grinding wheel

For use on 2003 and later Ford V8 Explorer, 2004 and later Ford F150 and Cadillac CS, Ford Super Duty Trucks, F250, F350 and F450

TEKTON 5686 4" 2-Jaw Gear Puller

Allows Technician to Remove Parking Brake Cable by Compressing the Spring, Supersedes 40800, Tool can be used when cable is still attached to parking brake assembly, Ends of tool are angled to allow easier access, Slots on each end allow tool to slip over cable instead of feeding the cable through the end of the tool, Especially useful on Ford F-Series, Expeditions, Excursions, etc.

TEKTON 5685 4" 3-Jaw Gear Puller

TEKTON 5750 13-pc. Harmonic Balance Puller
1-pc. Yoke
   1-pc. Center Screw
   1-pc. Center Screw Tip
   3-pc. 1/4" (18 TPI) x 2" Puller Bolts
   3-pc. 3/8" (24 TPI) x 2" Puller Bolts
   2-pc. 3/8" (16 TPI) x 3-3/4" Puller Bolts
   2-pc. 5/16" (20 TPI) x 3" Puller Bolts

TEKTON 5691 6" 2-Jaw Gear Puller

Head Adjusts to 5 Positions.  Two hook sizes easily remove most oil and grease seals, Where clearance is a problem, remove the pin to reposition the head, The adjustable head works great on front wheel drive transaxles, Also works on front crankshaft seals without removing the radiator

TEKTON 5690 6" 3-Jaw Gear Puller

Disconnects A/C and Quick Connect Fuel Lines, Made of durable plastic that resists fuels and solvents, Six sizes: 5/16", 3/8", 1/2", 5/8", 3/4" and 7/8"

Fork Width: 11/16"

Fork Width: 15/16"

TEKTON 5740 Pilot Bearing Puller

Used on Dodge and GM pickups, Cadillac, Jeep and other applications, Tool drives on the bolt flange, so the head of the retaining bolt is not destroyed

TEKTON 5541 2-Ton Power Puller

Heat-treated to resist bending on truck retention springs, Easily release SIR module retention springs on Gm cars, minivans and light trucks

Removes pressed-on alternator and power steering pulleys on late GM, Ford and Chrysler engines, Installs late model GM alternator and power steering pulleys including Quad 4,

Removes Battery Terminals and Bolted on Wiper Arms.  A dual-purpose puller. Easily removes stuck battery terminals, Tighten knurled cone to force jaws under the cable clamp, Turn center screw to lift clamp off terminal, Also removes bolted on windshield wiper arms that fit over a tapered spline, The puller screw pad is designed to fit the top of the spline post for easy pulling

TEKTON 5692 8" 3-Jaw Gear Puller

TEKTON 5632 9-pc. 5-lb. Slide Hammer Dent Puller Set
1-pc. 5-lb. Slide Hammer Puller (18 TPI)
   1-pc. Nose Adapter (18 TPI I.D. x 14 TPI O.D.)
   1-pc. Nose Cone (18 TPI x 24 TPI)
   1-pc. Metal Pulling Screw (14 TPI)
   1-pc. Pierce Punch (24 TPI x 13 TPI)
   2-pc. Puller Hooks
   1-pc. Plate Edge Puller
   1-pc. L-Puller

TEKTON 5546 4-Ton Power Puller

TEKTON 5542 2-Ton Dual Gear Power Puller